Introduction

This files defines EthTrcv MCAL configuration structures

Variables
struct EthTrcv_ConfigType_s	EthTrcvConfig_0_PC
	ETHTRCV Configuration struct declaration. More...

Macros
#define	ETHTRCV_PRE_COMPILE_VARIANT (STD_ON)
	ETHTRCV Build Variant. Build variant pre-compile (STD_ON/STD_OFF) More...

#define	ETHTRCV_MAX_CONTROLLER (2U)
	EthTrcv max number of controllers. More...

#define	ETHTRCV_MAX_CONTROLLER_CFGS (2U)
	EthTrcv max number of configurations. More...

#define	ETHTRCV_AUTONEG_STATUS_WAITCOUNT_TICKS (0x7d0U)
	EthTrcv auto-negotiation wait count Transceiver delay after auto-negotiation started to auto-negotiation completed. Transceiver (PHY) sets auto-negotiation status bit in status register once it is complete. Depending on Transceiver type, MDIO frequency it will take different time. change count value if transceiver detection fails in auto-negotiation. More...

#define	ETHTRCV_LINKSTATUS_WAITCOUNT_TICKS (0x7d0U)
	Wait for link status to become up after configuration. More...

#define	ETHTRCV_WAKEUPSUPPORT_API (ETHTRCV_WAKEUP_NOT_SUPPORTED)
	Enable/disable Ethernet transceiver EthTrcvWakeUpSupport APIs. More...

#define	ETHTRCV_SETTRANSCEIVERMODE_API (STD_ON)
	Enable/disable Ethernet transceiver settransceivermode API. More...

#define	ETHTRCV_GETTRANSCEIVERMODE_API (STD_ON)
	Enable/disable Ethernet transceiver gettransceivermodeapi API. More...

#define	ETHTRCV_STARTAUTONEGOTIATION_API (STD_ON)
	Enable/disable Ethernet transceiver startautonegotiation API. More...

#define	ETHTRCV_GETLINKSTATE_API (STD_ON)
	Enable/disable Ethernet transceiver getlinkstate API. More...

#define	ETHTRCV_GETBAUDRATE_API (STD_ON)
	Enable/disable Ethernet transceiver getbaudrate API. More...

#define	ETHTRCV_GETDUPLEXMODE_API (STD_ON)
	Enable/disable Ethernet transceiver getduplexmode API. More...

#define	ETHTRCV_GETPHYIDENTIFIER_API (STD_OFF)
	Enable/disable Ethernet transceiver getphyidentifier API. More...

#define	ETHTRCV_TIMEOUT_DURATION (160000U)
	ETH timeout. More...

#define	ETHTRCV_GETCABLEDIAGNOSTICSRESULT_API (STD_ON)
	Cabled diagnostic result. More...

#define	ETHTRCV_GETPHYSIGNALQUALITY_API (STD_ON)
	Signal quality. More...

#define	ETHTRCV_SETPHYLOOPBACKMODE_API (STD_ON)
	Set loopback mode. More...

#define	ETHTRCV_SETPHYTESTMODE_API (STD_ON)
	Set phy test mode. More...

#define	ETHTRCV_SETPHYTXMODE_API (STD_ON)
	Set phy tx mode. More...

#define	EthTrcvConf_EthTrcvConfig_EthTrcvConfig_0 (0U)
	EthTrcv controller ID Configured controller ID(s) More...

#define	ETHTRCV_DRV_CONFIG_0 ((const EthTrcv_ConfigType *) &EthTrcvConfig_0_PC)

EthTrcv Driver Service Id
The Service Id is one of the argument to Det_ReportError function and is used to identify the source of the error
#define	ETHTRCV_INIT_ID ((uint8) 0x01U)
	EthTrcv_Init() API Service ID. More...

#define	ETHTRCV_CONTROLLER_INIT_ID ((uint8) 0x02U)
	EthTrcv_Init() API Service ID. More...

#define	ETHTRCV_SETTRCVMODE_ID ((uint8) 0x03U)
	EthTrcv_SetTransceiverMode() API Service ID. More...

#define	ETHTRCV_GETTRCVMODE_ID ((uint8) 0x04U)
	EthTrcv_GetTransceiverMode() API Service ID. More...

#define	ETHTRCV_SRTAUTONEGOTIA_ID ((uint8) 0x05U)
	EthTrcv_StartAutoNegotiation() API Service ID. More...

#define	ETHTRCV_GETLNKSTATE_ID ((uint8) 0x06U)
	EthTrcv_GetLinkState() API Service ID. More...

#define	ETHTRCV_GETBAUD_ID ((uint8) 0x07U)
	EthTrcv_GetBaudRate() API Service ID. More...

#define	ETHTRCV_GETDPLXMODE_ID ((uint8) 0x08U)
	EthTrcv_GetDuplexMode() API Service ID. More...

#define	ETHTRCV_READMIIIND_ID ((uint8) 0x09U)
	EthTrcv_ReadMiiIndication callback() API Service ID. More...

#define	ETHTRCV_WRITEMIIIND_ID ((uint8) 0x0AU)
	EthTrcv_WriteMiiIndication callback() API Service ID. More...

#define	ETHTRCV_VERSION_ID ((uint8) 0x0BU)
	EthTrcv_GetVersionInfo() API Service ID. More...

#define	ETHTRCV_MAINFCT_WRITE_ID ((uint8) 0x0CU)
	EthTrcv_MainFunction() API Service ID. More...

#define	ETHTRCV_GETTRCVWKUPMODE_ID ((uint8) 0x0DU)
	EthTrcv_GetTransceiverWakeupMode() API Service ID. More...

#define	ETHTRCV_SETTRCVWKUPMODE_ID ((uint8) 0x0EU)
	EthTrcv_SetTransceiverWakeupMode() API Service ID. More...

#define	ETHTRCV_CHKWKUP_ID ((uint8) 0x0FU)
	EthTrcv_CheckWakeup() API Service ID. More...

#define	ETHTRCV_SETPHYTESTMODE_ID ((uint8) 0x10U)
	EthTrcv_SetPhyTestMode() API Service ID. More...

#define	ETHTRCV_SETPHYLOOPBACKMODE_ID ((uint8) 0x11U)
	EthTrcv_SetPhyLoopbackMode() API Service ID. More...

#define	ETHTRCV_GETPHYSIGNALQUALITY_ID ((uint8) 0x12U)
	EthTrcv_GetPhySignalQuality() API Service ID. More...

#define	ETHTRCV_SETPHYTXMODE_ID ((uint8) 0x13U)
	EthTrcv_SetPhyTxMode() API Service ID. More...

#define	ETHTRCV_GETCABLEDIAGNOSTICSRESULT_ID ((uint8) 0x014U)
	EthTrcv_GetCableDiagnosticsResult() API Service ID. More...

#define	ETHTRCV_GETPHYIDENTIFIER_ID ((uint8) 0x015U)
	EthTrcv_GetPhyIdentifier() API Service ID. More...

EthTrcv Driver Configuration SW Version Info
Pre-compile switches for enabling/disabling ETHTRCV MCAL APIs
#define	ETHTRCV_VERSION_INFO_API (STD_ON)
	Enable/Disable EthTrcv_GetVersionInfo() More...

#define	ETHTRCV_DEV_ERROR_DETECT (STD_ON)
	Enable/Disable DEV error detection. More...

EthTrcv Controller names
Symbolic names for the EthTrcvControllerId.
#define	ETHTRCV_CONTROLLER_ID_0 (0U)

EthTrcv Transceiver names
Symbolic names for the EthTrcv.
#define	ETHTRCV_CONTROLLER_ID_0_TRCV_ID_0 (0U)

EthTrcv Wake-up Modes
Ethernet Transceiver wakeup support definitions used to configure wake-up to polling or interrupt or to not used/not supported.
#define	ETHTRCV_WAKEUP_BY_INTERRUPT (0x0U)
	Interrupt based wake up for Ethernet Transceiver. More...

#define	ETHTRCV_WAKEUP_BY_POLLING (0x1U)
	Polling based wake up for Ethernet Transceiver. More...

#define	ETHTRCV_WAKEUP_NOT_SUPPORTED (0x2U)
	Wake up for Ethernet Transceiver not supported. More...

ETHTRCV DEM Error codes to report
Pre-compile switches for enabling/disabling DEM events
#define	DemConf_DemEventParameter_ETHTRCV_DEM_NO_EVENT (0xFFFFU)

#define	ETHTRCV_DEM_NO_EVENT DemConf_DemEventParameter_ETHTRCV_DEM_NO_EVENT

#define	ETHTRCV_E_HARDWARE_ERROR (ETHTRCV_DEM_NO_EVENT)
	Hardware failed. More...

#define	ETHTRCV_E_ACCESS (ETHTRCV_DEM_NO_EVENT)
	Hardware failed. More...

Macro Definition Documentation

◆ ETHTRCV_INIT_ID

#define ETHTRCV_INIT_ID ((uint8) 0x01U)

EthTrcv_Init() API Service ID.

◆ ETHTRCV_CONTROLLER_INIT_ID

#define ETHTRCV_CONTROLLER_INIT_ID ((uint8) 0x02U)

EthTrcv_Init() API Service ID.

◆ ETHTRCV_SETTRCVMODE_ID

#define ETHTRCV_SETTRCVMODE_ID ((uint8) 0x03U)

EthTrcv_SetTransceiverMode() API Service ID.

◆ ETHTRCV_GETTRCVMODE_ID

#define ETHTRCV_GETTRCVMODE_ID ((uint8) 0x04U)

EthTrcv_GetTransceiverMode() API Service ID.

◆ ETHTRCV_SRTAUTONEGOTIA_ID

#define ETHTRCV_SRTAUTONEGOTIA_ID ((uint8) 0x05U)

EthTrcv_StartAutoNegotiation() API Service ID.

◆ ETHTRCV_GETLNKSTATE_ID

#define ETHTRCV_GETLNKSTATE_ID ((uint8) 0x06U)

EthTrcv_GetLinkState() API Service ID.

◆ ETHTRCV_GETBAUD_ID

#define ETHTRCV_GETBAUD_ID ((uint8) 0x07U)

EthTrcv_GetBaudRate() API Service ID.

◆ ETHTRCV_GETDPLXMODE_ID

#define ETHTRCV_GETDPLXMODE_ID ((uint8) 0x08U)

EthTrcv_GetDuplexMode() API Service ID.

◆ ETHTRCV_READMIIIND_ID

#define ETHTRCV_READMIIIND_ID ((uint8) 0x09U)

EthTrcv_ReadMiiIndication callback() API Service ID.

◆ ETHTRCV_WRITEMIIIND_ID

#define ETHTRCV_WRITEMIIIND_ID ((uint8) 0x0AU)

EthTrcv_WriteMiiIndication callback() API Service ID.

◆ ETHTRCV_VERSION_ID

#define ETHTRCV_VERSION_ID ((uint8) 0x0BU)

EthTrcv_GetVersionInfo() API Service ID.

◆ ETHTRCV_MAINFCT_WRITE_ID

#define ETHTRCV_MAINFCT_WRITE_ID ((uint8) 0x0CU)

EthTrcv_MainFunction() API Service ID.

◆ ETHTRCV_GETTRCVWKUPMODE_ID

#define ETHTRCV_GETTRCVWKUPMODE_ID ((uint8) 0x0DU)

EthTrcv_GetTransceiverWakeupMode() API Service ID.

◆ ETHTRCV_SETTRCVWKUPMODE_ID

#define ETHTRCV_SETTRCVWKUPMODE_ID ((uint8) 0x0EU)

EthTrcv_SetTransceiverWakeupMode() API Service ID.

◆ ETHTRCV_CHKWKUP_ID

#define ETHTRCV_CHKWKUP_ID ((uint8) 0x0FU)

EthTrcv_CheckWakeup() API Service ID.

◆ ETHTRCV_SETPHYTESTMODE_ID

#define ETHTRCV_SETPHYTESTMODE_ID ((uint8) 0x10U)

EthTrcv_SetPhyTestMode() API Service ID.

◆ ETHTRCV_SETPHYLOOPBACKMODE_ID

#define ETHTRCV_SETPHYLOOPBACKMODE_ID ((uint8) 0x11U)

EthTrcv_SetPhyLoopbackMode() API Service ID.

◆ ETHTRCV_GETPHYSIGNALQUALITY_ID

#define ETHTRCV_GETPHYSIGNALQUALITY_ID ((uint8) 0x12U)

EthTrcv_GetPhySignalQuality() API Service ID.

◆ ETHTRCV_SETPHYTXMODE_ID

#define ETHTRCV_SETPHYTXMODE_ID ((uint8) 0x13U)

EthTrcv_SetPhyTxMode() API Service ID.

◆ ETHTRCV_GETCABLEDIAGNOSTICSRESULT_ID

#define ETHTRCV_GETCABLEDIAGNOSTICSRESULT_ID ((uint8) 0x014U)

EthTrcv_GetCableDiagnosticsResult() API Service ID.

◆ ETHTRCV_GETPHYIDENTIFIER_ID

#define ETHTRCV_GETPHYIDENTIFIER_ID ((uint8) 0x015U)

EthTrcv_GetPhyIdentifier() API Service ID.

◆ ETHTRCV_PRE_COMPILE_VARIANT

#define ETHTRCV_PRE_COMPILE_VARIANT (STD_ON)

ETHTRCV Build Variant. Build variant pre-compile (STD_ON/STD_OFF)

◆ ETHTRCV_VERSION_INFO_API

#define ETHTRCV_VERSION_INFO_API (STD_ON)

Enable/Disable EthTrcv_GetVersionInfo()

◆ ETHTRCV_DEV_ERROR_DETECT

#define ETHTRCV_DEV_ERROR_DETECT (STD_ON)

Enable/Disable DEV error detection.

◆ ETHTRCV_MAX_CONTROLLER

#define ETHTRCV_MAX_CONTROLLER (2U)

EthTrcv max number of controllers.

◆ ETHTRCV_MAX_CONTROLLER_CFGS

#define ETHTRCV_MAX_CONTROLLER_CFGS (2U)

EthTrcv max number of configurations.

◆ ETHTRCV_CONTROLLER_ID_0

#define ETHTRCV_CONTROLLER_ID_0 (0U)

◆ ETHTRCV_CONTROLLER_ID_0_TRCV_ID_0

#define ETHTRCV_CONTROLLER_ID_0_TRCV_ID_0 (0U)

◆ ETHTRCV_WAKEUP_BY_INTERRUPT

#define ETHTRCV_WAKEUP_BY_INTERRUPT (0x0U)

Interrupt based wake up for Ethernet Transceiver.

◆ ETHTRCV_WAKEUP_BY_POLLING

#define ETHTRCV_WAKEUP_BY_POLLING (0x1U)

Polling based wake up for Ethernet Transceiver.

◆ ETHTRCV_WAKEUP_NOT_SUPPORTED

#define ETHTRCV_WAKEUP_NOT_SUPPORTED (0x2U)

Wake up for Ethernet Transceiver not supported.

◆ ETHTRCV_AUTONEG_STATUS_WAITCOUNT_TICKS

#define ETHTRCV_AUTONEG_STATUS_WAITCOUNT_TICKS (0x7d0U)

EthTrcv auto-negotiation wait count Transceiver delay after auto-negotiation started to auto-negotiation completed. Transceiver (PHY) sets auto-negotiation status bit in status register once it is complete. Depending on Transceiver type, MDIO frequency it will take different time. change count value if transceiver detection fails in auto-negotiation.

◆ ETHTRCV_LINKSTATUS_WAITCOUNT_TICKS

#define ETHTRCV_LINKSTATUS_WAITCOUNT_TICKS (0x7d0U)

Wait for link status to become up after configuration.

◆ ETHTRCV_WAKEUPSUPPORT_API

#define ETHTRCV_WAKEUPSUPPORT_API (ETHTRCV_WAKEUP_NOT_SUPPORTED)

Enable/disable Ethernet transceiver EthTrcvWakeUpSupport APIs.

◆ ETHTRCV_SETTRANSCEIVERMODE_API

#define ETHTRCV_SETTRANSCEIVERMODE_API (STD_ON)

Enable/disable Ethernet transceiver settransceivermode API.

◆ ETHTRCV_GETTRANSCEIVERMODE_API

#define ETHTRCV_GETTRANSCEIVERMODE_API (STD_ON)

Enable/disable Ethernet transceiver gettransceivermodeapi API.

◆ ETHTRCV_STARTAUTONEGOTIATION_API

#define ETHTRCV_STARTAUTONEGOTIATION_API (STD_ON)

Enable/disable Ethernet transceiver startautonegotiation API.

◆ ETHTRCV_GETLINKSTATE_API

#define ETHTRCV_GETLINKSTATE_API (STD_ON)

Enable/disable Ethernet transceiver getlinkstate API.

◆ ETHTRCV_GETBAUDRATE_API

#define ETHTRCV_GETBAUDRATE_API (STD_ON)

Enable/disable Ethernet transceiver getbaudrate API.

◆ ETHTRCV_GETDUPLEXMODE_API

#define ETHTRCV_GETDUPLEXMODE_API (STD_ON)

Enable/disable Ethernet transceiver getduplexmode API.

◆ ETHTRCV_GETPHYIDENTIFIER_API

#define ETHTRCV_GETPHYIDENTIFIER_API (STD_OFF)

Enable/disable Ethernet transceiver getphyidentifier API.

◆ ETHTRCV_TIMEOUT_DURATION

#define ETHTRCV_TIMEOUT_DURATION (160000U)

ETH timeout.

◆ ETHTRCV_GETCABLEDIAGNOSTICSRESULT_API

#define ETHTRCV_GETCABLEDIAGNOSTICSRESULT_API (STD_ON)

Cabled diagnostic result.

◆ ETHTRCV_GETPHYSIGNALQUALITY_API

#define ETHTRCV_GETPHYSIGNALQUALITY_API (STD_ON)

Signal quality.

◆ ETHTRCV_SETPHYLOOPBACKMODE_API

#define ETHTRCV_SETPHYLOOPBACKMODE_API (STD_ON)

Set loopback mode.

◆ ETHTRCV_SETPHYTESTMODE_API

#define ETHTRCV_SETPHYTESTMODE_API (STD_ON)

Set phy test mode.

◆ ETHTRCV_SETPHYTXMODE_API

#define ETHTRCV_SETPHYTXMODE_API (STD_ON)

Set phy tx mode.

◆ DemConf_DemEventParameter_ETHTRCV_DEM_NO_EVENT

#define DemConf_DemEventParameter_ETHTRCV_DEM_NO_EVENT (0xFFFFU)

◆ ETHTRCV_DEM_NO_EVENT

#define ETHTRCV_DEM_NO_EVENT DemConf_DemEventParameter_ETHTRCV_DEM_NO_EVENT

◆ ETHTRCV_E_HARDWARE_ERROR

#define ETHTRCV_E_HARDWARE_ERROR (ETHTRCV_DEM_NO_EVENT)

Hardware failed.

◆ ETHTRCV_E_ACCESS

#define ETHTRCV_E_ACCESS (ETHTRCV_DEM_NO_EVENT)