Introduction

Data Structures
struct	SDL_pokShiftsAndMasks_t

POK types
This enumerator defines the possible POK module types
typedef uint8_t	SDL_pok_type

#define	SDL_TYPE_POK ((SDL_pok_type) 1U)

#define	SDL_TYPE_POK_SA ((SDL_pok_type) 2U)

POK/POR hysteresIs types
This enumerator defines the possible hysteresis control values for the Power Subsystem modules
typedef uint8_t	SDL_pwrss_hysteresis

#define	SDL_PWRSS_SET_HYSTERESIS_DISABLE ((SDL_pwrss_hysteresis) 0U)

#define	SDL_PWRSS_SET_HYSTERESIS_ENABLE ((SDL_pwrss_hysteresis) 1U)

#define	SDL_PWRSS_GET_HYSTERESIS_VALUE ((SDL_pwrss_hysteresis) 2U)

#define	SDL_PWRSS_HYSTERESIS_NO_ACTION ((SDL_pwrss_hysteresis) 3U)

POK/POR TRIM values
This enumerator defines the possible trim value for POK/POR modules Any value between 0 through 127 is valid TRIM value * * POK \| Under Voltage \| Over Voltage \| * \| Detection \| Detection \| Step Resolution * ----------- \| --------------- \| ---------------- \| ---------------- * CORE_POK \| 475mV - 1.35V \| 725mV - 1.65V \| 0.0125V * POK1.8 \| 1.432V - 2.168V \| 1.432V - 2.168V \| 0.02V * POK3.3 \| 2.625V - 3.975V \| 2.625V - 3.975V \| 0.0375V * *
typedef uint8_t	SDL_pwrss_trim

#define	SDL_PWRSS_MAX_TRIM_VALUE ((SDL_pwrss_trim) 127U)

#define	SDL_PWRSS_TRIM_NO_ACTION ((SDL_pwrss_trim) 128U)

#define	SDL_PWRSS_GET_TRIM_VALUE ((SDL_pwrss_trim) 129U)

#define	SDL_PWRSS_INVALID_TRIM_VALUE ((SDL_pwrss_trim) 255U)

POK/POR Voltage detection modes
This enumerator defines the possible values of Voltage Detection modes
typedef uint8_t	SDL_pwrss_vd_mode

#define	SDL_PWRSS_SET_UNDER_VOLTAGE_DET_ENABLE ((SDL_pwrss_vd_mode) 0U)

#define	SDL_PWRSS_SET_OVER_VOLTAGE_DET_ENABLE ((SDL_pwrss_vd_mode) 1U)

#define	SDL_PWRSS_SET_PP_VOLTAGE_DET_ENABLE ((SDL_pwrss_vd_mode) 2U)

#define	SDL_PWRSS_GET_VOLTAGE_DET_MODE ((SDL_pwrss_vd_mode) 2U)

#define	SDL_PWRSS_VOLTAGE_DET_NO_ACTION ((SDL_pwrss_vd_mode) 3U)

POK detection status
This enumerator defines the POK Detection status values
typedef uint8_t	SDL_POK_detection_status

#define	SDL_POK_DETECTION_DISABLED ((SDL_POK_detection_status) 0U)

#define	SDL_POK_DETECTION_ENABLED ((SDL_POK_detection_status) 1U)

POK detection values
This enumerator defines the POK Detection values
typedef uint8_t	SDL_POK_detection

#define	SDL_POK_DETECTION_DISABLE ((SDL_POK_detection) 0U)

#define	SDL_POK_DETECTION_ENABLE ((SDL_POK_detection) 1U)

#define	SDL_POK_DETECTION_NO_ACTION ((SDL_POK_detection) 2U)

#define	SDL_POK_GET_DETECTION_VALUE ((SDL_POK_detection) 3U)

POK Enable Selection source Values
This enumerator defines the POK Enable selection source Selection source values
typedef uint8_t	SDL_POK_enSelSrc

#define	SDL_POK_ENSEL_HWTIEOFFS ((SDL_POK_enSelSrc) 0U)

#define	SDL_POK_ENSEL_PRG_CTRL ((SDL_POK_enSelSrc) 1U)

#define	SDL_POK_ENSEL_NO_ACTION ((SDL_POK_enSelSrc) 2U)

#define	SDL_POK_GET_ENSEL_VALUE ((SDL_POK_enSelSrc) 3U)

POK voltage threshold status
This enumerator defines the Voltage threshold status
typedef uint8_t	SDL_POK_thrStatus

#define	SDL_VOLTAGE_ABOVE_THRESHOLD ((SDL_POK_thrStatus) 0U)

#define	SDL_VOLTAGE_BELOW_THRESHOLD ((SDL_POK_thrStatus) 1U)

#define	SDL_VOLTAGE_GOOD ((SDL_POK_thrStatus) 2U)

POK trim selection values from HHV default or CTRL registers
This enumerator defines the trim selection values
typedef uint8_t	SDL_por_trim_sel

#define	SDL_POR_TRIM_SELECTION_FROM_HHV_DEFAULT ((uint8_t) 0U)

#define	SDL_POR_TRIM_SELECTION_FROM_CTRL_REGS ((uint8_t) 1U)

#define	SDL_POR_TRIM_SELECTION_NO_CHANGE ((uint8_t) 2U)

#define	SDL_POR_TRIM_SELECTION_GET_VALUE ((uint8_t) 3U)

POR POR Override enable and set
This enumerator defines the override enable/set values /set
typedef uint8_t	SDL_por_override

#define	SDL_POR_OVERRIDE_NOT_SET_DISABLE ((SDL_por_override) 0U)

#define	SDL_POR_OVERRIDE_NOT_SET_ENABLE ((SDL_por_override) 1U)

#define	SDL_POR_OVERRIDE_SET_DISABLE ((SDL_por_override) 2U)

#define	SDL_POR_OVERRIDE_SET_ENABLE ((SDL_por_override) 3U)

#define	SDL_POR_GET_OVERRIDE_VALUE ((SDL_por_override) 4U)

#define	SDL_POR_SET_OVERRIDE_NO_CHANGE ((SDL_por_override) 5U)

#define	SDL_OVERRIDE_SET_UNKNOWN ((SDL_por_override) 0xFFU)

POR POR Override index
This enumerator defines the override index values
#define	SDL_PORHV_OVERRIDE_INDEX (0U)

#define	SDL_BGAP_OVERRIDE_INDEX (1U)

#define	SDL_POKHV_OVERRIDE_INDEX (2U)

#define	SDL_POKLVA_OVERRIDE_INDEX (3U)

#define	SDL_POKLVB_OVERRIDE_INDEX (4U)

#define	SDL_MAX_OVERRIDE_INDEX (5U)

POR Module state values
This enumerator defines the POR Module State
typedef uint8_t	SDL_por_module_status

#define	SDL_POR_MODULE_STATUS_FUNCTIONAL_MODE ((SDL_por_module_status) 0U)

#define	SDL_POR_MODULE_STATUS_RESET_MODE ((SDL_por_module_status) 1U)

POK POK ID values
This enumerator defines the possible POK module ID values on J721E
typedef SDL_wkup_ctrl_mmr_cfg0Regs	SDL_wkupCtrlRegsBase_t

Macro Definition Documentation

◆ SDL_TYPE_POK

#define SDL_TYPE_POK ((SDL_pok_type) 1U)

POK type Power System Module

◆ SDL_TYPE_POK_SA

#define SDL_TYPE_POK_SA ((SDL_pok_type) 2U)

POK_SA type Power System Module

◆ SDL_PWRSS_SET_HYSTERESIS_DISABLE

#define SDL_PWRSS_SET_HYSTERESIS_DISABLE ((SDL_pwrss_hysteresis) 0U)

Disable hysteresis for the module

◆ SDL_PWRSS_SET_HYSTERESIS_ENABLE

#define SDL_PWRSS_SET_HYSTERESIS_ENABLE ((SDL_pwrss_hysteresis) 1U)

Enable hysteresis for the module

◆ SDL_PWRSS_GET_HYSTERESIS_VALUE

#define SDL_PWRSS_GET_HYSTERESIS_VALUE ((SDL_pwrss_hysteresis) 2U)

Get hysteresis value for the module

◆ SDL_PWRSS_HYSTERESIS_NO_ACTION

#define SDL_PWRSS_HYSTERESIS_NO_ACTION ((SDL_pwrss_hysteresis) 3U)

No update on hysteresis for the module

◆ SDL_PWRSS_MAX_TRIM_VALUE

#define SDL_PWRSS_MAX_TRIM_VALUE ((SDL_pwrss_trim) 127U)

TRIM is 7 bit value, when the trim value is <= to the MAX value, that value would be written to trim register Any other values, would be treated as the command as described belowTRIM is 7 bit value, and hence the maximum value is 127

◆ SDL_PWRSS_TRIM_NO_ACTION

#define SDL_PWRSS_TRIM_NO_ACTION ((SDL_pwrss_trim) 128U)

No update on trim value read/write for the module

◆ SDL_PWRSS_GET_TRIM_VALUE

#define SDL_PWRSS_GET_TRIM_VALUE ((SDL_pwrss_trim) 129U)

Command to read the TRIM value

◆ SDL_PWRSS_INVALID_TRIM_VALUE

#define SDL_PWRSS_INVALID_TRIM_VALUE ((SDL_pwrss_trim) 255U)

Invalid TRIM value

◆ SDL_PWRSS_SET_UNDER_VOLTAGE_DET_ENABLE

#define SDL_PWRSS_SET_UNDER_VOLTAGE_DET_ENABLE ((SDL_pwrss_vd_mode) 0U)

Enable under voltage detection for the module

◆ SDL_PWRSS_SET_OVER_VOLTAGE_DET_ENABLE

#define SDL_PWRSS_SET_OVER_VOLTAGE_DET_ENABLE ((SDL_pwrss_vd_mode) 1U)

Enable over voltage detection for the module

◆ SDL_PWRSS_SET_PP_VOLTAGE_DET_ENABLE

#define SDL_PWRSS_SET_PP_VOLTAGE_DET_ENABLE ((SDL_pwrss_vd_mode) 2U)

Enable ping-pong voltage detection for the module

◆ SDL_PWRSS_GET_VOLTAGE_DET_MODE

#define SDL_PWRSS_GET_VOLTAGE_DET_MODE ((SDL_pwrss_vd_mode) 2U)

Get voltage detection for the module

◆ SDL_PWRSS_VOLTAGE_DET_NO_ACTION

#define SDL_PWRSS_VOLTAGE_DET_NO_ACTION ((SDL_pwrss_vd_mode) 3U)

No update on voltage detection mode update for the module

◆ SDL_POK_DETECTION_DISABLED

#define SDL_POK_DETECTION_DISABLED ((SDL_POK_detection_status) 0U)

POK Detection disabled

◆ SDL_POK_DETECTION_ENABLED

#define SDL_POK_DETECTION_ENABLED ((SDL_POK_detection_status) 1U)

POK Detection Enabled

◆ SDL_POK_DETECTION_DISABLE

#define SDL_POK_DETECTION_DISABLE ((SDL_POK_detection) 0U)

POK Detection disabled

◆ SDL_POK_DETECTION_ENABLE

#define SDL_POK_DETECTION_ENABLE ((SDL_POK_detection) 1U)

POK Detection Enabled

◆ SDL_POK_DETECTION_NO_ACTION

#define SDL_POK_DETECTION_NO_ACTION ((SDL_POK_detection) 2U)

POK Detection No action

◆ SDL_POK_GET_DETECTION_VALUE

#define SDL_POK_GET_DETECTION_VALUE ((SDL_POK_detection) 3U)

POK Detection get value

◆ SDL_POK_ENSEL_HWTIEOFFS

#define SDL_POK_ENSEL_HWTIEOFFS ((SDL_POK_enSelSrc) 0U)

POK enables come from hardware tie offs

◆ SDL_POK_ENSEL_PRG_CTRL

#define SDL_POK_ENSEL_PRG_CTRL ((SDL_POK_enSelSrc) 1U)

POK enables come from CTRLMMR_WKUP_PRG0_CTRL register

◆ SDL_POK_ENSEL_NO_ACTION

#define SDL_POK_ENSEL_NO_ACTION ((SDL_POK_enSelSrc) 2U)

POK enable selection no action

◆ SDL_POK_GET_ENSEL_VALUE

#define SDL_POK_GET_ENSEL_VALUE ((SDL_POK_enSelSrc) 3U)

POK enable selection Get value

◆ SDL_VOLTAGE_ABOVE_THRESHOLD

#define SDL_VOLTAGE_ABOVE_THRESHOLD ((SDL_POK_thrStatus) 0U)

◆ SDL_VOLTAGE_BELOW_THRESHOLD

#define SDL_VOLTAGE_BELOW_THRESHOLD ((SDL_POK_thrStatus) 1U)

◆ SDL_VOLTAGE_GOOD

#define SDL_VOLTAGE_GOOD ((SDL_POK_thrStatus) 2U)

◆ SDL_POR_TRIM_SELECTION_FROM_HHV_DEFAULT

#define SDL_POR_TRIM_SELECTION_FROM_HHV_DEFAULT ((uint8_t) 0U)

Trim selections for Bandgap and PORs come from HHV defaults

◆ SDL_POR_TRIM_SELECTION_FROM_CTRL_REGS

#define SDL_POR_TRIM_SELECTION_FROM_CTRL_REGS ((uint8_t) 1U)

Trim selections for Bandgap and POKs come from CTRLMMR_WKUP_POR_BANDGAP_CTRL and POR_POKxxx_CTRL registers

◆ SDL_POR_TRIM_SELECTION_NO_CHANGE

#define SDL_POR_TRIM_SELECTION_NO_CHANGE ((uint8_t) 2U)

Trim selections for Bandgap and POKs No Change

◆ SDL_POR_TRIM_SELECTION_GET_VALUE

#define SDL_POR_TRIM_SELECTION_GET_VALUE ((uint8_t) 3U)

Trim Read selections Bandgap and POKs

◆ SDL_POR_OVERRIDE_NOT_SET_DISABLE

#define SDL_POR_OVERRIDE_NOT_SET_DISABLE ((SDL_por_override) 0U)

OVERRIDE IS NOT SET and DISABLED

◆ SDL_POR_OVERRIDE_NOT_SET_ENABLE

#define SDL_POR_OVERRIDE_NOT_SET_ENABLE ((SDL_por_override) 1U)

OVERRIDE IS NOT SET and ENABLED

◆ SDL_POR_OVERRIDE_SET_DISABLE

#define SDL_POR_OVERRIDE_SET_DISABLE ((SDL_por_override) 2U)

OVERRIDE IS SET and DISABLED

◆ SDL_POR_OVERRIDE_SET_ENABLE

#define SDL_POR_OVERRIDE_SET_ENABLE ((SDL_por_override) 3U)

OVERRIDE IS SET and ENABLED

◆ SDL_POR_GET_OVERRIDE_VALUE

#define SDL_POR_GET_OVERRIDE_VALUE ((SDL_por_override) 4U)

PORHV GET OVERRIDE VALUE

◆ SDL_POR_SET_OVERRIDE_NO_CHANGE

#define SDL_POR_SET_OVERRIDE_NO_CHANGE ((SDL_por_override) 5U)

PORHV SET OVERRIDE VALUE NO CHANGE

◆ SDL_OVERRIDE_SET_UNKNOWN

#define SDL_OVERRIDE_SET_UNKNOWN ((SDL_por_override) 0xFFU)

OVRD and SET Values unknown

◆ SDL_PORHV_OVERRIDE_INDEX

#define SDL_PORHV_OVERRIDE_INDEX (0U)

PORHV Override index

◆ SDL_BGAP_OVERRIDE_INDEX

#define SDL_BGAP_OVERRIDE_INDEX (1U)

Bandgap Override index

◆ SDL_POKHV_OVERRIDE_INDEX

#define SDL_POKHV_OVERRIDE_INDEX (2U)

POKHV Override index

◆ SDL_POKLVA_OVERRIDE_INDEX

#define SDL_POKLVA_OVERRIDE_INDEX (3U)

POKLVA Override index

◆ SDL_POKLVB_OVERRIDE_INDEX

#define SDL_POKLVB_OVERRIDE_INDEX (4U)

POKLVB Override index

◆ SDL_MAX_OVERRIDE_INDEX

#define SDL_MAX_OVERRIDE_INDEX (5U)

total Number of Override indices

◆ SDL_POR_MODULE_STATUS_FUNCTIONAL_MODE

#define SDL_POR_MODULE_STATUS_FUNCTIONAL_MODE ((SDL_por_module_status) 0U)

POR in functional mode

◆ SDL_POR_MODULE_STATUS_RESET_MODE

#define SDL_POR_MODULE_STATUS_RESET_MODE ((SDL_por_module_status) 1U)

POR in Reset mode

Typedef Documentation

◆ SDL_pok_type

typedef uint8_t SDL_pok_type

◆ SDL_pwrss_hysteresis

typedef uint8_t SDL_pwrss_hysteresis

◆ SDL_pwrss_trim

typedef uint8_t SDL_pwrss_trim

◆ SDL_pwrss_vd_mode

typedef uint8_t SDL_pwrss_vd_mode

◆ SDL_POK_detection_status

typedef uint8_t SDL_POK_detection_status

◆ SDL_POK_detection

typedef uint8_t SDL_POK_detection

◆ SDL_POK_enSelSrc

typedef uint8_t SDL_POK_enSelSrc

◆ SDL_POK_thrStatus

typedef uint8_t SDL_POK_thrStatus

◆ SDL_por_trim_sel

typedef uint8_t SDL_por_trim_sel

◆ SDL_por_override

typedef uint8_t SDL_por_override

◆ SDL_por_module_status

typedef uint8_t SDL_por_module_status

◆ SDL_wkupCtrlRegsBase_t

typedef SDL_wkup_ctrl_mmr_cfg0Regs SDL_wkupCtrlRegsBase_t