OSPI_v0.h File Reference

Introduction

OSPI driver implementation for OSPI IP V0 controller.

============================================================================

The SPI header file should be included in an application as follows:

#include <ti/drv/spi/SPI.h>
#include <ti/drv/spi/soc/SPI_soc.h>

This OSPI driver implementation is designed to operate on IP V0 OSPI controller

---

Go to the source code of this file.

Data Structures
struct	OSPI_dmaInfo
	OSPI UDMA info structure. More...
struct	OSPI_v0_HwAttrs
	OSPI IP V0 Hardware attributes. More...
struct	OSPI_v0_Object
	OSPI IP V0 driver object. More...

Macros
#define	OSPI_V0_CMD_SET_CFG_MODE   (OSPI_CMD_RESERVED + 0U)
	Set SPI controller into CONFIG Mode. More...
#define	OSPI_V0_CMD_SET_XFER_MODE   (OSPI_CMD_RESERVED + 1U)
	Set SPI controller into Transfer Mode. More...
#define	OSPI_V0_CMD_XFER_MODE_RW   (OSPI_CMD_RESERVED + 2U)
	Set direction of data flow when in memory mapped mode. More...
#define	OSPI_V0_CMD_XFER_OPCODE   (OSPI_CMD_RESERVED + 3U)
	Set flash specific command when in indirect transfer mode. More...
#define	OSPI_V0_CMD_SET_XFER_LINES   (OSPI_CMD_RESERVED + 4U)
	Set number of lines configured for RX/TX operation. More...
#define	OSPI_V0_CMD_RD_DUMMY_CLKS   (OSPI_CMD_RESERVED + 5U)
	Set number of dummy clock cycles for read operation. More...
#define	OSPI_V0_CMD_CFG_PHY   (OSPI_CMD_RESERVED + 6U)
	Set command to configure phy. More...
#define	OSPI_V0_CMD_ENABLE_DDR   (OSPI_CMD_RESERVED + 7U)
	Set command to enable DDR mode. More...
#define	OSPI_V0_CMD_CFG_XIP   (OSPI_CMD_RESERVED + 8U)
	Set command to enable XIP mode. More...
#define	OSPI_V0_CMD_ENABLE_SDR   (OSPI_CMD_RESERVED + 9U)
	Set command to disable DDR mode. More...
#define	OSPI_V0_CMD_XFER_OPCODE_EXT   (OSPI_CMD_RESERVED + 10U)
	Set extended opcodes when in indirect transfer mode. More...
#define	OSPI_V0_CMD_EXT_RD_DUMMY_CLKS   (OSPI_CMD_RESERVED + 11U)
	Set extended opcode command read dummy cycles. More...
#define	OSPI_V0_CMD_CFG_RD_DELAY   (OSPI_CMD_RESERVED + 12U)
	Set read capture delay. More...
#define	OSPI_V0_CMD_CFG_DUMMY_CYCLE   (OSPI_CMD_RESERVED + 13U)
	Set dummy cycles in flash device. More...
#define	OSPI_V0_CMD_EXT_RD_CMD_LEN   (OSPI_CMD_RESERVED + 14U)
	Set extended opcode command read dummy cycles. More...

Enumerations
enum	SPI_TransactionType { SPI_TRANSACTION_TYPE_READ = 0, SPI_TRANSACTION_TYPE_WRITE }
	Type of the SPI transaction. More...
enum	OSPI_OperMode { OSPI_OPER_MODE_CFG = 0U, OSPI_OPER_MODE_IND_XFER, OSPI_OPER_MODE_DAC_XFER }
	OSPI controller modes. More...
enum	OSPI_xferLines { OSPI_XFER_LINES_SINGLE = 0U, OSPI_XFER_LINES_DUAL, OSPI_XFER_LINES_QUAD, OSPI_XFER_LINES_OCTAL }
	Number of lines used for OSPI read/write transaction. More...

Functions
uint32_t	OSPI_getReadDataCapDelay (SPI_Handle handle)

Variables
const OSPI_FxnTable	OSPI_FxnTable_v0